Free planning tool · no account needed

Deck Resurfacing Planner

Replacing the decking on a sound frame costs far less than a ground-up build. Enter your existing deck footprint, board width and gap, waste allowance, and the decking you want, and this planner returns a board takeoff, linear feet, hidden-fastener clip counts, and an installed cost band. A short frame-reuse checklist tells you when the honest answer is a rebuild conversation instead.

  • Every calculation runs in your browser
  • Nothing you type is uploaded or stored
  • Planning band only, never a quote
Existing deck footprint

Measure the frame you are keeping, not the boards you are removing. Most residential decks land between 6 and 40 ft on each side.

New decking and board gap

Composite and PVC boards are about 5.5 in. wide and want a gap near 3/16 in. (0.1875). Nominal 2x6 wood is 5.5 in. wide; a 2x4 is 3.5 in.

Layout, waste, and stock

A straight run over a square frame rarely needs more than 10%. Add more for diagonal layouts, stair treads, a picture-frame border, or a frame that is out of square.

Frame reuse checklist

Answer from what you can see. Anything you mark no or not sure is advisory only — it points at what to have checked before you buy decking.

Walk the deck and look between boards. Soft spots, dark streaks, or a springy feel point at joists that will not hold new decking.

The ledger is the board bolted to the house and the most common place a deck fails. Look for stained siding, loose bolts, or missing metal flashing above it.

Push against a post and watch where it meets the ground. Movement, cracked concrete, or buried wood ends all change the plan.

Joist hangers, bolts, and brackets should be solid and lightly weathered, not flaking or stained.

Stringers carry the most load per board on the whole deck, and rotted stringers are usually visible from the side.

Grab a post and try to rock it. Guard posts take the highest point load of anything on a deck.

Your re-deck plan

Price guidance dated 2026-09-01

Fill in the footprint, decking, and frame checklist, then choose Plan my re-deck to see how many boards to buy, the linear feet and clip count, and the installed cost band.

How the resurfacing planner works

  1. Measure the frame you are keeping. Width runs along the house and depth runs away from it. Those two numbers multiply into the deck area that drives both the takeoff and the cost band.
  2. Set the board width and gap. A 5.5 in. board with a 3/16 in. gap covers about 5.69 in. of deck per row. Narrower boards mean more rows, more clips, and more linear feet.
  3. Choose the material. Composite and PVC boards take hidden clips; wood decking is face fastened. The material choice sets the per-square-foot allowance on top of the published installation rate.
  4. Add a waste allowance. Waste covers cut-offs at the ends of rows, boards that come in damaged, and the extra pieces a diagonal or picture-frame layout needs.
  5. Answer the frame checklist. The checklist is the part that keeps the planner honest: if the frame is not reusable, the takeoff below is for a project that should not start yet.

What the plan includes — and what it leaves out

In the band

  • Decking material allowance for the material you picked
  • Installation at the published basic rate of $9.74 to $12.43 per sq ft
  • Board takeoff with waste, stock lengths, and cut-off per row
  • Hidden fastener clips for grooved composite, PVC, and hardwood decking
  • An advisory frame-reuse reading with the next step for each flag

Not in the band

  • Tearing out and hauling away the old decking
  • Railing, stairs, fascia, or picture-frame borders
  • Joist, ledger, post, or footing repairs found under the boards
  • Permits, engineering, HOA review, or inspections
  • Lighting, fans, fire pits, or privacy screens

Worked examples

20 × 12 ft frame re-decked in composite

A 240 sq ft frame with 5.5 in. boards, a 3/16 in. gap, and boards running parallel to the house needs 26 rows of decking, about 520 linear ft of coverage, and roughly 572 linear ft of board once the waste allowance is added. Grooved composite at 16 in. joist spacing takes about 432 hidden clips.

25 × 10 ft re-deck in pressure-treated wood

Deck Bros published a pressure-treated re-deck at roughly $5,000 for a 25 × 10 ft deck, which is about $20 per sq ft installed. This planner lands the same footprint inside its planning band when you pick pressure-treated decking.

When the answer is not a re-deck

If the checklist comes back with rotted joists, a compromised ledger, or moving posts, the planner switches to a rebuild conversation. New decking is the cheapest part of a deck; hiding a failing frame under it is the most expensive mistake in this trade.

Deck resurfacing questions homeowners ask

Is re-decking cheaper than building a new deck?

Yes, when the frame, posts, and footings are sound. You are paying for decking and installation instead of footings, posts, beams, joists, and the picture-frame border, which is why a re-deck is usually completed within a working day.

How do I know whether my frame can be reused?

Walk the deck and look for soft spots, dark streaks, a springy feel, stained siding above the ledger, or movement in posts and railings. The checklist above turns those observations into a reading, but it is a self-check and not a structural ruling — a free assessment that pulls a few boards gives you the real answer.

Why does the planner ask about hidden fastener clips?

Grooved composite, PVC, and hardwood boards fasten with clips at every joist crossing, and those clips are ordered by the box. Rows plus one clip per joist line is the count crews use to get close, so you can budget the fastener line instead of discovering it mid-build.

Can I re-deck over the old boards?

No. Deck Bros removes the existing decking so the joists, ledger, and hardware can be inspected before new boards go down. Layering new decking over old hides rot, traps moisture, and adds weight the frame was never sized for.

Do the numbers get sent anywhere?

No. The takeoff and the cost band are calculated in your browser and are never uploaded or stored. Use Copy plan or Download takeoff if you want to keep them, because nothing is saved when you close the tab.

Turn the takeoff into a fixed price

Deck Bros is a family-owned Omaha deck builder that installs new decking on existing structures across the Omaha metro, Lincoln, and Western Iowa. Estimates are free, many can be handled same-day over the phone, and installation work carries the same 5-year workmanship warranty as a full build.

Get Your QuoteSee what deck installation covers

Deck Resurfacing Planner · planning takeoff only · price guidance dated 2026-09-01. © 2026 Deck Bros.